>NAME >NAME >NAME >VALUE CAPACITOR chip >NAME >NAME >VALUE >NAME TSL1401CL 128px LINEAR CMOS >NAME AD7940 14-bit 100kSPS ADC >NAME >VALUE >VALUE TAOS TSL1401CL 128-Pixel Linear CMOS Array with Hold, Analog Out, 3-5V Supply Analog Devices AD7940 14-bit ADC, 100k Samples/sec sample rate, 2.5-5V single supply Capacitor Standard 0603 ceramic capacitor, and 0.1" leaded capacitor. SUPPLY SYMBOL <h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find resistors, capacitors, inductors, test points, jumper pads, etc. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing: CC v3.0 Share-Alike You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. >Name >Value >NAME >Name >Value >Name >Value CAPACITOR chip >NAME >VALUE >NAME >VALUE 1007 (2518 metric) package >NAME >VALUE >Name >Value >NAME >VALUE >NAME >VALUE 1.3x1.3mm 1.7mm between. Fits Sumida CDRH2D09, CDRH2D18 inductor >NAME >VALUE >NAME >VALUE >Name >Value >Name >Value Small solder jumper with big paste layer so it will short during reflow. >NAME >VALUE Solder jumper, small, shorted with trace. No paste layer. Trace is cuttable. >NAME >VALUE >NAME >VALUE Small solder jumper with no paste layer so it will open after reflow. >NAME >VALUE >NAME >VALUE >NAME >VALUE Inductors Basic Inductor/Choke - 0603 and 1206. Footprints are not proven and vary greatly between part numbers. Solder Jumper Standard SMD solder jumper. Used to automate production. Two varients : Normally Open and Normally Closed are the same, but have different paste layers. NC will have a large amount of paste and should jumper during reflow. <h3>SparkFun Electronics' preferred foot prints</h3> In this library you'll find connectors and sockets- basically anything that can be plugged into or onto. We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com. Licensing: CC v3.0 Share-Alike You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE >VALUE >NAME Header 7 Standard 7-pin 0.1" header. Use with straight break away headers (SKU : PRT-00116), right angle break away headers (PRT-00553), swiss pins (PRT-00743), machine pins (PRT-00117), and female headers (PRT-00115). NOTES ON THE VARIANTS LOCK and LOCK_LONGPADS... This footprint was designed to help hold the alignment of a through-hole component (i.e. 7-pin header) while soldering it into place. You may notice that each hole has been shifted either up or down by 0.005 of an inch from it's more standard position (which is usually a perfectly straight line). This slight alteration caused the pins (the squares in the middle) to touch the edges of the holes. Because they are alternating, it causes a "brace" to hold the header in place. 0.005 has proven to be the perfect amount of "off-center" position when using our standard breakaway headers. Although looks a little odd when you look at the bare footprint, once you have a header in there, the alteration is very hard to notice. Also, if you push a header all the way into place, it is covered up entirely on the bottom side. This idea of altering the position of holes to aid alignment will be further integrated into the Sparkfun Library for other footprints. It can help hold any component with 3 or more connection pins. Low-pass (Pi) Filter Cut-off Freq ~150kHz Short if AD7940 ADC is not populated to use JP1 pin 3 as the TSL1401CL analog out. OPEN MINI SPECTROMETER REVISION 1 (SEPTEMBER 1 2013) DESIGNER: PETER JANSEN WWW.TRICORDERPROJECT.ORG LICENSE: CC-BY-SA 3.0 UNPORTED